Paint for socles and facades Farbex | POLYSAN

Paint for socles and facades Farbex

Paint for socles and facades Farbex

Farbex

Paint for socles and facades

Buy

Specification

  • advanced resistance to weather effects, mechanic load, UV-rays and temperature fluctuation
  • it creates a water-resistant coating
  • advanced durability of the coating

Sphere of application

It is intended for coating of mineral surfaces (concrete bases, mortar plasters), which socles and facades of the buildings are made of and other surfaces. The paint can be applied on the surfaces previously coated with water-based, alkyd and oily paint products. It is recommended for coating of concrete bases to protect concrete against carbonization and to prevent corrosion of ferroconcrete constructions.

Technical data

Consumption standard of 1 layer:
110-210 g/m2
Diluent:
Water
Application:
It is applied with a roller, a brush or a spraying gun.
Drying period (23 °С, 50% RH):
2 hours
Color base:
A (white) and C (semi transparent), is tinted according to NCS color range.
Solids content (DSTU ISO 3251):
52-54 %
Density (DSTU ISO 2811-1) :
1,27-1,3 g/cm3
Gloss (DSTU ISO 2813) :
Max.10 GU at 85°
Dry film thickness:
100-200 mikron
Particle size:
Maximum 30 mikron
Vapor permeability (EN ISO 7783-2) :
30-100 g/(m2*day)
Water permeability (DSTU EN 1062-3) :
maximum 0,1 kg/(m2* h0,5)
Marking acc. to the DSTU EN 1062-1:
G3|E3|S1|V2|W3|A0|C0
Warranty period:
18 months from the date of manufacturing
Packaging:
1,2 kg, 3,5 kg, 6 kg, 12 kg

Color

beige
white
cherry
brown
cream rosy
sandy
light brown
light-grey
grey
black

Gloss

matt

Application instruction

Preliminary preparation

Uncoated surface: Clean it from fragile parts till hard base surface. Remove dust, oil, grease and other dirt.

Previously coated surface: Clean thoroughly the surface from old loose coatings (loose coats of paint or varnish) in a manual (a wire brush or a scraper,) thermal (hot air dryer, infrared radiation) or chemical (a paint removing solution) ways. Remove chalk and lime chalk whitewash till the hard base layer in a mechanical way. Clean the surface from all kinds of dirt. Sandpaper the surface, which was previously coated with alkyd or oil enamel. After that treat the surface as the uncoated one.

Non-significant defects of mineral surfaces shall be corrected with Finishing Putty TM Farbex. Polish the surface after that.

It is recommended to treat the surface with Antiseptic product TM Farbex for protection against mould and fungi.

Priming

Previously treated mineral and wooden surfaces need no undercoating.

Previously treated absorbing mineral surfaces shall be undercoated with acrylic deep-penetrating primer TM Farbex.

Previously uncoated wooden surfaces shall be primed with a wood protective acrylic primer TM Maxima.

Applying of finishing layer

Stir the paint thoroughly before application. The paint shall be applied at the temperature from +10 ºС till +30 ºС and relative air humidity up to 80%.

ATTENTION! We recommend applying the same batch  the finishing coat of the paint to avoid differences in shades of the color. If you use the product of different batches it is necessary to mix it.

Do not apply paint under direct sunlight, strong wind, frost and precipitation. The surface shall not be affected with precipitation or subzero temperatures for 8 hours after the paint is applied.

Tool cleaning

Rinse thoroughly the tools with water after application.

X

Flow calculator

Consumption standard of 1 layer
min
max

When calculating the area to be painted, you need to subtract the area that will not be painted. (windows, doors, etc.)

Paint consumption may vary depending on dilution and uniformity of application of the paint.