DekArt
Ultra White
Snow-white interior paint for walls and ceilings
Specification
The paint visually enlightens space, due to its high degree of whiteness. Snow-white paint doesn't yellow through the time. It creates matt coating which lets the walls "breathe" well. The product is applied easily and doesn't splash while applying.
Sphere of application
It is intended for interior coating of all mineral (mortar and lime-mortar plaster, finishing plaster, brick, concrete), gypsum and wooden surfaces, wallpaper and fiberglass. It is recommended for coating of walls and ceilings in dry spaces with low exploitation load: living, administrative spaces, medical, infant and educational establishments, spaces of catering and industrial enterprises.
Tinting
It can be tinted manually with Pigment Concentrate Farbex Color, other waterborne coloring pastes or with a coloring machine acc. to NCS color range and others.
Content
Technical data
| Consumption standard of 1 layer | 150-200 g/m2. It depends on the way of application and type of the surface. |
| Thinner | Water . Max.10% delution of the total weight is allowed. |
| Application | Apply with a roller, a brush or a spraying gun. |
| Drying period (23 °С, 50% RH) | max. 1 hour. Drying period increases if the temperature is getting down and relative air humidity is increasing. |
| Solids content (DSTU ISO 3251) |
52,5±2 % |
| Density (DSTU ISO 2811-1) | ≈ 1,47 g/cm3 |
| Gloss (DSTU ISO 2813) | Max. 10 GU at 85° , (matt, DSTU EN 13300) |
| The degree of milling (SSU ISO 1524) | max. 15 microns , (fine-grained, DSTU EN 13300) |
| Contrast ratio of dry film (ISO 6504-3) | 97 - 98%, 3 class of hiding power (acc. to DSTU EN 13300) |
| Wet-scrub resistance class (DSTU EN 13300) | 5 |
| VOC content (ISO 11890) | - |
| Warranty period | 18 months |
| Packaging | 1,2 kg, 4 kg, 6,3 kg, 12,6 kg, 20 kg |
Gloss
Color
Application instruction
-
1. Surface preparation
Uncoated surface: Clean it from loose coatings, dust, oil, grease and other dirt. After that apply finishing layer of plaster on the whole surface with Finishing putty TM Farbex.
Previously coated surfaces: Clean thoroughly the surface from old loose coatings (loose paint and varnish) in mechanical (a scraper, a wire brush), thermal (hot air fan, infrared radiation) or chemical way (paint removal solutions). Chalk and lime-chalk coatings shall be removed mechanically till hard surface. Clean the surface also from other dirt. Surfaces, previously coated with alkyd and oil enamel, shall be sandpapered. Then treat it as uncoated surface.
Small defects of mineral surface shall be corrected with finishing putty TM Farbex and sandpaper after that.
For protection against mould and fungi it is recommended to treat the surface with antiseptic TM Farbex.
2. Priming
Previously treated mineral and wooden surfaces need no undercoating.
Previously untreated absorbing mineral surfaces shall be undercoated with Deep-penetrating primer "Base" TM DekArt for better adhesion and to make absorbing capacity of the surface uniform.
Previously untreated wooden surfaces shall be undercoated with Acrylic wood primer ТМ Maxima.
3. Application
Stir the paint thoroughly before application. If it is required dilute it with water. Over-dilution makes the quality of the surface worse! Application is performed at the temperature from + 5 °С till + 35 °С and relative air humidity no more than 80%. Apply the paint in 1-2 coats with a brush, a roller, or a spraying gun.
4. Tool cleaning
Clean tools with water after application. Do not let them dry. Dry product shall be removed from the
Flow calculator
Consumption standard of 1 layer
When calculating the area to be painted, you need to subtract the area that will not be painted. (windows, doors, etc.)
Paint consumption may vary depending on dilution and uniformity of application of the paint.