Farbex
Емаль стирол-акрилова для радіаторів опалення
Specification
- Snow-white color. It does not become yellow with time.
- It is resistant to repeated washing and mechanical load.
- It is intended for the surfaces, previously coated with alkyd enamels.
- It dries quickly.
- It has high adhesive properties on different kinds of surfaces.
Sphere of application
The product is intended for decorative and protective coating of undercoated or previously coated radiators and elements of heating systems and also for undercoated wooden, metal and mineral surfaces.
Tinting
It can be tinted manually with Pigment Concentrate Farbex Color, other waterborne coloring pastes or with a coloring machine acc. to NCS color range and others.
Content
Technical data
| Consumption standard of 1 layer | 85-115 g/m2, it depends on the type of surface and the way of application. |
| Thinner | Water. It is allowed to dilute up to 10 % of the total weight of the product |
| Application | Apply with a brush, a roller or a spraying gun. |
| Drying period (23 °С, 50% RH) | 2 hours. Drying period increases if the temperature is getting down and relative air humidity is increasing. |
| Solids content (DSTU ISO 3251) |
49±2 % |
| The degree of milling (SSU ISO 1524) | maximum 10 micron |
| Density (DSTU ISO 2811-1) | ≈ 1,15 g/cm3 |
| Hardness (DSTU ISO 1522) | > 10 sec |
| Gloss (DSTU ISO 2813) | minimum 60 GU at 60° |
| Wet-scrub resistance, microns (DSTU ISO 11998) | < 1 (after 200 erase cycles) |
| VOC content (ISO 11890) | < 20 g/l. |
| Warranty period | 18 months |
| Packaging | 0,75 l (0,85 kg), 3 kg, (20 kg if pre-ordered) |
Gloss
Color
Application instruction
-
1. Surface preparation
The surface shall be hard and dry. Clean thoroughly of dust, rust, dirt, coke dross, grease, oil and other dirt.
Clean dirty areas with a dry brush.
To receive a smooth surface without visible places of old coatings (paint or varnish), it shall be totally removed from the surface in mechanical (with a scratcher, a floor scrubber), thermal (a hot dryer, infra-red rays) or chemical way (paint removing treatments).
Previously painted surface (with oil or alkyd paint) shall be sanded for gaining the best adhesion.
Defected surfaces (holes, rends, cracks) shall be filled with Putty for wood ТМ Farbex.
Small defects of mineral surface shall be corrected with Finishing putty TM Farbex.
Metal surface shall be thoroughly cleaned from rust with a metal brush or polishing paper.
The puttied surface shall be polished till it is smooth, remove dust after polishing.
2. Priming
Previously coated wooden surfaces require no undercoating.
Wooden surfaces, which were not undercoated before, shall be treated with Acrylic woodcare primer TM Maxima.
The uncoated mineral absorbing surfaces shall be undercoated with Deep-penetrating waterborne acrylic primer “SuperBase” TM Farbex.
Metal surfaces, which were not undercoated before, shall be undercoated with Anticorrosion primer GF-021 TM Farbex.
3. Applying
Stir the enamel thoroughly before use. The enamel is ready to use. Excessive diluting causes the quality of the coating.
The temperature of the air and the surface under application shall be from +15 °С till +35 °С and relative air humidity no more than 80%.
Enamel shall be applied with brush, roller or paint blower with 1-2 layers. The next layer shall be applied not earlier than in 4 hours.
The coating takes finally its properties in 3-4 weeks.
It is not recommended to perform an application on working heating systems!
4. Tool cleaning
Clean tools with water after application.
Flow calculator
Consumption standard of 1 layer
When calculating the area to be painted, you need to subtract the area that will not be painted. (windows, doors, etc.)
Paint consumption may vary depending on dilution and uniformity of application of the paint.