Maxima
Эмаль алкидная для радиаторов отопления
Specification
- it is snow-white doesn’t yellow through the time
- it resists high temperatures (up to +80°C)
- it resists washing with detergents and disinfectants
- it has a permanent gloss
- it had a perfect adhesion
Sphere of application
It is intended for coating of heating radiators, any wooden and undercoated metal surfaces under constant thermal effect indoors and outdoors.
Content
Technical data
| Consumption standard of 1 layer | 40-60 g/m2, depending on the way of application and type of surface. |
| Thinner | Оdorless solvent ТМ Maxima, 10% maximum of the total enamel weight. |
| Application | Apply with a brush, a roller or a spraying gun. |
| Drying period (23 °С, 50% RH) | 18 hours. Drying period increases if the temperature is getting down and relative air humidity is getting higher. |
| Solids content (DSTU ISO 3251) |
68±2 % |
| Density (DSTU ISO 2811-1) | ≈ 1,2 g/cm3 |
| Gloss (DSTU ISO 2813) | 85-90 GU (at 60º) |
| Non-volatile matter by volume (DSTU ISO 3233) |
51±2 % |
| VOC content (ISO 11890) | ≈ 385 g/l |
| Warranty period | 36 months from the date of manufacturing. |
| Packaging | 0,7 kg |
Gloss
Color
Application instruction
-
1. Surface preparation
Metal surfaces:
new ones - clean of dust, dirt and the degrease.
previously coated, old surfaces shall be clean of peeled and loose paint products till hard surface in a mechanical (a scraper, a wire brush), thermal (a hot air dryer, infrared radiation) or chemical (paint removing products) ways. Clean the surface thoroughly of corrosion with a wire brush or sandpaper. Treat the surface coated with oil or alkyd-based paint with sandpaper for better adhesion.
Wooden surfaces:
new ones - clean of dust and dirt.
previously coated, old surfaces shall be clean of peeled and loose paint products till hard surface in a mechanical (a scraper, a wire brush), thermal (a hot air dryer, infrared radiation) or chemical (paint removing products) ways. Avoid ways of cleaning which can damage the timber (e.g. a sandblast apparatus). Hallows, cracks or uneven areas, existing on the surface shall be corrected with a putty for wooden and mineral surfaces TM Farbex. Polish the surface after that till smooth condition. Remove abrasive dust.
2. Priming
Previously coated surfaces need no undercoating.
Iron surfaces, which were not previously coated shall be undercoated with Anticorrosion primer GP-021 TM "Farbex".
Wooden surfaces, which were not previously coated shall be undercoated with Wood protective primer "Base" TM "Maxima".
3. Applying
Do not apply the enamel on heated pipes and radiators!
Stir the enamel thoroughly till homogeneous condition. Dilute the enamel till working viscosity if necessary.
ADVICE: Apply the enamel in 1-2 thin coats instead of 1 thick coat for more quality paint coating! Apply a subsequent coat in 18 hours after the previous application.
The application shall be performed at the temperature of air and the surface from +10 ºС till +30 ºС and relative air humidity less than 80%. Do not apply the products under direct sunlight, strong wind and precipitations. The coating shall not be affected by precipitations for 24 hours after application.
Complete hardening of the surface and achieving its properties is in 14 days.
4. Tool cleaning
Clean tools with a solvent and then with warm water with detergents if necessary.
Flow calculator
Consumption standard of 1 layer
When calculating the area to be painted, you need to subtract the area that will not be painted. (windows, doors, etc.)
Paint consumption may vary depending on dilution and uniformity of application of the paint.