Floor Enamel wearproof Maxima

Floor Enamel wearproof Maxima


Floor Enamel wearproof



  • It dries quickly.
  • It has a high degree and stability of gloss and intense color.
  • It creates a long-lasting, hard, elastic coating with high resistance to abrasion, cracks, scratches and intensive moving (walking).
  • It is remarkable with economic and easy application.
  • It is resistant to the effect of water and detergents.

Sphere of application

It is intended for high-quality coating of new and renovation of old wooden and concrete floors indoors.

Technical data

Consumption standard of 1 layer 50-90 g/m2, depending on the way of application and type of surface.
Solvent odorless solvent TM Maxima, 10% maximum of the total enamel weight.
Application Apply with a brush, a roller or a spraying gun.
Drying period (23 °С, 50% RH) 8 hours. Drying period increases if the temperature is getting down and relative air humidity is getting higher.
Solids content
(DSTU ISO 3251)
64,5±2 %
Density (DSTU ISO 2811-1) 1,12 – 1,14 g/cm3
Gloss (DSTU ISO 2813) 85-90 GU(at 60º)
Hardness (DSTU ISO 1522) ≈ 40 sec., Konig pendulum.
Non-volatile matter by volume
(DSTU ISO 3233)
49±2 %
VOC content (ISO 11890) 400±5 g/l.
Warranty period 36 monthsfrom the date of manufacturing.
Packaging 0,7 kg, 2,3 kg




Due to the nature of the screens, color tones may differ from actual colors.

Application instruction


1. Surface preparation

The surface shall be dry and clean of dust, dirt and grease.

Remove old peeled paint and also weak loose coats till the hard base surface in a mechanical (a scraper, a wire brush), thermal (a hot air drier, infrared radiation) or chemical (paint removing products) way. 

Treat the surfaces, previously coated with oily or alkyd paints, with sandpaper for better adhesion.

Hollows, cracks or uneven areas of the surface shall be corrected with Putty for wooden and mineral surfaces Farbex.

Correct non-significant defects of mineral surface with finishing putty Farbex and then polish it.

The plastered surface shall be polished till a smooth condition. Then remove abrasive dust.


2. Priming

Previously coated surfaces need no undercoating.

Previously uncoated wooden surfaces shall be undercoated with Wood-protective product "Base" TM "Maxima". Make sure that the surface is clean and dry before applying the primer.

Previously uncoated concrete surfaces shall be undercoated with a solution of the enamel and solvent at the ratio of 1:1.


3. Applying of finishing layer

Stir the enamel thoroughly till homogeneous condition. Dilute the enamel till working viscosity with a solvent if necessary. Use the paint of the same batch for the finishing coat to avoid differences in the shade of color. If use the paint of different batches mix them obligatory.

Apply the enamel in 1-2 thin coats. Do not apply the enamel with a thick coat! Apply a subsequent coat in 8 hours after the previous one.

Apply the enamel at the temperature of air and the surface from +10 ºС till +30 ºС and relative air humidity less than 80%.

Complete hardening of the surface and achieving of its properties is in 14 days.

4. Tool cleaning

Clean tools with a solvent and then with warm water with detergents if necessary.


Alkyd Floor Enamel Maxima
Одним із видів лакофарбових матеріалів є емаль ПФ-266, яка застосовується для фарбування дерев’яних та мінеральних підлог. Завдяки своїм технічним характеристикам емаль алкідна ПФ-266 утворює покриття з високою міцністю та еластичністю, яке витримує експлуатаційні навантаження, зберігаючи стійкий блиск та насиченість кольорів. Така емаль стійка до впливу води та миючих засобів, а також утворює однорідну та гладку глянцеву поверхню. Емаль алкідна для підлоги в нашому асортименті має різний час висихання: 8 годин та 24 години. Основними кольорами алкідної емалі є :
  • червоно-коричневий;
  • золотаво-коричневий;
  • жовто-коричневий.



Flow calculator

Consumption standard of 1 layer

When calculating the area to be painted, you need to subtract the area that will not be painted. (windows, doors, etc.)

Paint consumption may vary depending on dilution and uniformity of application of the paint.