Specification
- it is weatherproof
- it is resistant to temperature fluctuation
- it is water repellent
Sphere of application
It is intended for coating of wooden and metal surfaces under weather effects. It can be used as an additive to alkyd enamels to improve gloss.
Content
Technical data
| Consumption standard of 1 layer | 60-100 ml/m2 , depending on the type of surface and the way of application. |
| Solvent | solvent TM DekART or odorless solvent ТМ Maxima , 10% maximum of the total varnish weight. |
| Application | Apply with a brush, a spraying gun or dipping method. |
| Drying period (23 °С, 50% RH) | 24 hours. Drying period increases if the temperature is getting down and relative air humidity is getting higher. |
| Solids content (DSTU ISO 3251) | > 40 % |
| Density (DSTU ISO 2811-1) | 0,9±0.02 g/cm3 |
| Gloss (DSTU ISO 2813) | > 100 GU (at 60º) |
| Hardness (DSTU ISO 1522) | > 25 s., Konig pendulum. |
| Non-volatile matter by volume (DSTU ISO 3233) |
46,5±2 % |
| VOC content (ISO 11890) | ≤ 399 g/l |
| Warranty period | 18 months from the date of manufacturing. |
| Packaging | 0,45 kg (0,5 l) |
Gloss
Color
Application instruction
-
1. Preliminary preparation
Metal surfaces:
new ones shall be clean of dirt, dust and grease.
previously coated, old ones shall be treated to remove old loose and weak layers of coatings in mechanical (a scraper, a wire brush), thermal (hot air dryer, infrared radiation) or chemical (paint removing products) way. Clean thoroughly of corrosion with a wire brush or sandpaper. Treat the surface with small-grained sandpaper. Remove abrasive dust from the surface and degrease it.
Wooden surfaces:
new ones shall be cleaned of dirt, dust.
previously coated, old ones shall be treated to remove all applied coats in mechanical (a scraper, a wire brush), thermal (hot air dryer, infrared radiation) or chemical (paint removing products) way. Avoid methods of cleaning, which can damage timber (e.x. sandblast apparatus). Hollows, existing on wooden surface, or damage areas shall be corrected with Putty for wooden and mineral surface TM Farbex. Sandpaper the plastered surface till the smooth surface. Remove abrasive dust from the surface.
surfaces, previously treated with varnish - remove peeled varnish coatings. Sandpaper the surface till matt outlook. Remove abrasive dust from the surface.
2. Priming
Previously coated wooden surfaces don’t require undercoating.
Previously uncoated wooden surfaces shall be obligatorily undercoated. Make sure that the surface is clean and completely dry before undercoating. New or cleaned of old coatings, wooden surfaces shall be undercoated with Wood protective primer ТМ Maxima for maximal protective effect and even color. Edges of wooden surfaces shall be treated more carefully until they are completely soaked.
3. Application
Make sure that the undercoated surface is dry enough before applying a finishing coat. If necessary, dilute it with a solvent. Apply varnish in 1-2 coats with intermediate polishing. Apply each next layer not before 24 hours. Perform application at the temperature of air and the surface from +10 ºС till +35 ºС and relative air humidity less than 80 %. Do not apply the varnish under direct sunlight, strong wind and precipitations. The surface shall not be affected with precipitation during 24 hours after application. Complete hardening of the surface and obtaining of its properties is in 14 days.
4. Tool cleaning
Clean tools with a solvent and then with warm water and detergents if necessary.
Flow calculator
Consumption standard of 1 layer
When calculating the area to be painted, you need to subtract the area that will not be painted. (windows, doors, etc.)
Paint consumption may vary depending on dilution and uniformity of application of the paint.