Silk Touch 20 Semi-matt interior latex paint Maxima | POLYSAN

Silk Touch 20 Semi-matt interior latex paint Maxima

Silk Touch 20


Silk Touch 20

Semi-matt interior latex paint



Latex paint with silky effect. It has perfect adhesion and easily spreads on the surface, providing little consumption with high application rate. It creates hard coat resistant to intensive repeated washing (1 class acc. to DSTU EN 13300). It is vapor permeable. It hides effectively micro cracks of the surface under application. It is easy to apply, makes no runs and doesn't splash during application. It can be tinted manually with pigment concentrate Farbex Color, other waterborne coloring pastes or with a coloring machine acc. to NCS color range and others.

Sphere of application

It is intended for application on mineral surfaces (mortar and lime-mortar plaster, putty, gypsum, brick, concrete), wooden surfaces, wallpapers and fiberglass wallpaper indoors.

It is intended for coating of walls and ceilings with normal and advanced humidity indoors: living spaces and offices, bedrooms, halls, stair ways, showrooms, clubs, working spaces, etc. It is not intended for coating of floors, doors and furniture.

Technical data

Consumption standard of 1 layer:
110-150 g/m2
It is applied with a roller, a brush or a spraying gun.
Drying period (23 °С, 50% RH):
max. 1 hour
Solids content (DSTU ISO 3251) :
ab. 55 %
Density (DSTU ISO 2811-1) :
ab. 1,3 g/cm3
Gloss (DSTU ISO 2813) :
Max. 20 GU at 60°
The degree of milling (SSU ISO 1524):
max. 15 microns
Contrast ratio of dry film (ISO 6504-3) :
min. 99 %
Wet-scrub resistance (DSTU ISO 11998), microns:
max. 5 (after 200 cycles)
Warranty period:
36 months
1,2 kg, 3,5 kg, 6 kg, 12 kg


white (base A)



Application instruction

Surface preparation

Non-coated surface: Clean the surface from loose coatings, dust, oil, grease and other dirt. Use warm water to clean the surface. Use special detergents to clean extremely dirty areas. After that apply a layer of finishing putty TM Farbex, then sandpaper the surface.

Previously coated surfaces: Clean thoroughly the surface from old loose coatings (loose paint and varnish) mechanically (a scraper, a wire brush), thermally (hot air fan, infrared radiation) or chemically (paint removal solutions). Chalk and lime-chalk coatings shall be removed till hard surface mechanically. Clean the surface also from other dirt. Surfaces, previously coated with alkyd and oil enamel, shall be sandpapered. Then treat it as non-coated surface.

Small defects of mineral surface shall be corrected with finishing putty TM Farbex and sandpaper after that.

For protection against mould and fungi it is recommended to treat the surface with antiseptic TM Farbex.


Previously treated surfaces need no undercoating.

Previously non-coated absorbing mineral surfaces  shall be undercoated with acrylic deep-penetrating primer concentrate Super Base 1:4 TM Farbex. Dilute the primer according to the type of the surface (see directions for use for primer).

Applying of finishing layer

Stir the paint thoroughly before application. If it is required dilute it with water (max. 10% of the total weight of the paint). Over-dilution makes the quality of the surface worse! Application is performed at the temperature from + 5 °С till + 35 °С. Apply the paint in 1-2 coats with a brush, a roller or a spraying gun.

Tool cleaning

Rinse the tools with water after appliction. Do not let them dry. Rests of dried paint can be removed mechanically.


Flow calculator

Consumption standard of 1 layer

When calculating the area to be painted, you need to subtract the area that will not be painted. (windows, doors, etc.)

Paint consumption may vary depending on dilution and uniformity of application of the paint.