Maxima
Емаль акрилова для радіаторів опалення
Specification
- Snow-white color. It does not become yellow with time.
- It is resistant to high temperatures (maximum +80 °C).
- It is resistant to repeated washing and mechanical load.
- It has high adhesive properties on different kinds of surfaces.
Sphere of application
It is intended for decorative and protective coating of undercoated or previously coated radiators and elements of heating, and also undercoated metal surfaces.
Tinting
It can be tinted manually with Pigment Concentrate Farbex Color, other waterborne coloring pastes or with a coloring machine acc. to NCS color range and others.
Content
Technical data
| Consumption standard of 1 layer | 70-100 ml/m2, depending of the type of surface and way of application. |
| Thinner | Water. It is allowed to delute it maximum 10 % of the total weight. |
| Application | It is applied with a roller, a brush or a spraying gun. |
| Drying period (23 °С, 50% RH) | < 2 hour. Drying period increases if the temperature is getting down and relative air humidity is increasing. |
| Solids content (DSTU ISO 3251) |
45±2 % |
| The degree of milling (SSU ISO 1524) | ≈ 5 microns |
| Density (DSTU ISO 2811-1) | ≈ 1,17 g/cm3 |
| Hardness (DSTU ISO 1522) | > 50 sec. |
| Gloss (DSTU ISO 2813) | minimum 60 GU at 60° |
| Wet-scrub resistance, microns (DSTU ISO 11998) | < 1 (after 200 cycles) |
| VOC content (ISO 11890) | < 100 g/l |
| Warranty period | 36 months from the date of manufacturing (at the temperature from +5 °С till +35 °С) |
| Packaging | 0,75 L (20 kg if preordered) |
Gloss
Color
Application instruction
-
1. Preliminary preparation
The surface shall be hard and dry. Clean thoroughly of dust, rust, dirt, coke dross, grease, oil and other dirt.
Clean dirty areas with a dry brush.
The metal surface shall be thoroughly cleaned from rust with metal brush or polishing paper.
To receive a smooth surface without visible places of old coatings (paint or varnish), it shall be totally removed from the surface in mechanical (with a scratcher, a floor scrubber), thermal (a hot dryer, infra-red rays) or chemical way (paint removing treatments).
Previously painted surface (with oil or alkyd paint) shall be sanded for gaining the best adhesion.
2. Priming
Previously coated wooden surfaces require no undercoating.
Metal surfaces, which were not undercoated before, shall be undercoated with Anticorrosion primer GF-021 TM Farbex.
3. Applying of finishing layer
Stir the enamel thoroughly before use. The enamel is ready to use. If necessary, dilute it with water. Excessive diluting causes the quality of the coating.
It is not recommended to perform an application on working heating systems!
Enamel shall be applied with brush, roller or paint blower with 1-2 layers. Next layer shall be applied not earlier than in 4 hours. The temperature of the air and the surface under application shall be from +10 °С till +30 °С and relative air humidity no more than 80%.
Do not apply the enamel under direct sunlight, strong wind, frost and atmospheric precipitation. After the coating is applied it shall not be affected by atmospheric precipitation and sub-zero temperatures for 24 hours.
The coating takes finally its properties in 3-4 weeks.
4. Tool cleaning
Clean tools with water after application.
You may also be interested in
Flow calculator
Consumption standard of 1 layer
When calculating the area to be painted, you need to subtract the area that will not be painted. (windows, doors, etc.)
Paint consumption may vary depending on dilution and uniformity of application of the paint.