Maxima
Metal Enamel 3 in 1, smooth
Specification
- It is a metal enamel 3 in 1, which functionally joints: adhesion primer, anticorrosion protection and finishing enamel;
- It creates an anticorrosion film on the surface, which protects the metal surface against moisture and wind, rust creation;
- It creates coating, which is resistant to water, weather effects, industrial oils, domestic detergents;
- The enamel has high adhesion to the base surface.
Sphere of application
Metal enamel is intended for protection against corrosion and for decorative finishing of metal surfaces and also for wooden surfaces indoors and outdoors.
Technical data
| Consumption standard of 1 layer | 40-60 ml/m2 |
| Solvent | Оdorless solvent ТМ Maxima |
| Application | Apply with a brush, a roller or a spraying gun. |
| Drying period (23 °С, 50% RH) | 8 hours. |
| Solids content (DSTU ISO 3251) |
60-66 % |
| Density (DSTU ISO 2811-1) | 1,03 - 1,13 g/cm3 |
| Gloss (DSTU ISO 2813) | 80-90 GU |
| Hardness (DSTU ISO 1522) | ab. 35 sec |
| Warranty period | 36 months |
| Packaging | 0,75 l, 2,5 l (10 and 20 l - if preordered) |
Gloss
Color
Application instruction
1. Surface preparation
Metal surfaces:
new surfaces shall be clean of dust, dirt and degreased.
previously coated and old surfaces shall be cleaned from loose and peeled coats of paint products till hard base surface in a mechanical (a scraper, a wire brush), thermal (a hot air dryer, infrared radiation) or chemical (paint removing products) ways. Clean thoroughly of corrosion with a wire brush or sandpaper. Treat the surface previously coated with oily or alkyd-based paints for better adhesion.
Wooden surfaces:
new surfaces shall be clean of dust, dirt.
previously coated and old surfaces shall be cleaned from loose and peeled coats of paint products till hard base surface in a mechanical (a scraper, a wire brush), thermal (a hot air dryer, infrared radiation) or chemical (paint removing products) ways. Avoid methods of cleaning, which can damage timber (e.g. sandblast apparatus). Hollows, cracks and uneven areas shall be corrected with Putty for wood and mineral surfaces TM Farbex. Sandpaper the surface till smooth condition. Remove abrasive dust after that.
2. Priming
Metal surfaces need not advanced undercoating.
Undercoat wooden surfaces with alkyd wood protective primer TM Maxima. Make sure that the wooden surface is clean and completely dry before applying the primer.
3. Application
Stir the enamel thoroughly till homogeneous condition before application. Dilute the enamel with a solvent to working viscosity if necessary.
ADVICE: Apply 2 coats of the product to achieve the best possible properties of the coating instead of 1 thin coat. Apply each subsequent coat in 1 hour.
Perform application at the temperature of air and the surface from +10 ºС till +35 ºС and relative air humidity less than 80%. Do not apply the product under direct sunlight, strong wind and precipitations. The coating shall not be affected by precipitations for 24 hours after application.
Complete hardening of the surface and achieving of its properties is in 14 days.
4. Tool cleaning
Clean tools with a solvent and then with warm water with detergents if necessary.
You may also be interested in
References
Enamels 3 in 1 Maxima
Емаль 3 в 1 – це емаль по металу, яка функціонально об’єднує в собі: адгезійну ґрунтовку, захист від корозії та фінішну емаль. Антикорозійна емаль застосовується для фарбування металевих, дерев’яних та мінеральних поверхонь. Завдяки своїм характеристикам, емалі по металу створюють надійний захист від корозії та надають естетичний зовнішній вигляд. Антикорозійну емаль використовують для захисту та декорування різних металевих виробів, будівельних конструкцій, сільськогосподарської техніки, металевих вікон, шаф та дверей, як всередині, так і ззовні приміщень. Основні переваги емалей 3 в 1:- не потребує попереднього застосування ґрунтовки;
- можна наносити відразу на іржу, що дозволить вам зекономити час;
- легко наноситься;
- низька норма витрати.
повністю
Flow calculator
Consumption standard of 1 layer
When calculating the area to be painted, you need to subtract the area that will not be painted. (windows, doors, etc.)
Paint consumption may vary depending on dilution and uniformity of application of the paint.