It is one-component, quickly-drying primer enamel. It is resistant to UV radiation and weather effects. It contains anticorrosion additives, which provide reliable protection of metal surfaces. It has good adhesion to the surface.
It is intended for anticorrosion protection and decorative coating of metal surfaces (industrial metal constructions, technological equipment, agricultural machinery, engines, bridges, road fencing and alike), as well as for wooden, concrete and other surfaces outdoors and indoors.
Consumption standard of 1 layer | 70-100 g/m2 |
Thinner | Universal thinner TM Maxima |
Application | Apply with a brush, a roller or a spraying gun. |
Drying period (23 °С, 50% RH) | 1 hour. |
Solids content (DSTU ISO 3251) |
56-60 % |
Non-volatile matter by volume (DSTU ISO 3233) |
47-51 % |
Density (DSTU ISO 2811-1) | ab. 1,1 g/cm3 |
Gloss (DSTU ISO 2813) | ab. 80 GU |
Hardness (DSTU ISO 1522) | ab. 45 sec. |
VOC content (ISO 11890) | 430-490 g/l |
Warranty period | 24 months |
Packaging | 0,75 kg, 2,5 kg, 20 kg, 45 kg |
It is recommended to dry the surface and thoroughly clean it from dust, grease and rests of salt and other dirt for more quality coating on the surface.
Clean metal surfaces shall be treated with sandpaper for better adhesion. After that remove abrasion dust and degrease with a thinner.
Previously coated metal surfaces shall be cleaned in mechanical (with a scratcher or wire brush), thermal (with a hot air fan, IR radiation), or chemical (products for paint removal) way. The surface shall also be thoroughly cleaned from salt depositions and other dirt with a wire brush or rough sandpaper. After that remove abrasive dust and degrease with a thinner.
Previously coated wooden surfaces shall be cleaned from loose paint products in mechanical (with a scraper, a wire brush), thermal (with a hot air fan, IR radiation) or chemical (products for paint removal) way, treat with sandpaper. Abrasive dust shall be removed.
Metal surfaces need no advanced undercoating.
Wooden surfaces shall be undercoated with alkyd wood protective primer TM Maxima. Make sure that the wooden surface is clean and completely dry before applying the primer.
The undercoated concrete surfaces shall be primed with a mix of primer-enamel and Universal thinner TM Maxima in ratio of 1:1.
Stir the primer-enamel thoroughly before use.
Apply primer-enamel in 2 layers to obtaining optimal coating properties. Apply each next layer no later than after 1 hour.
Perform application at the temperature of air and the surface from +10 ºС till +25 ºС and relative air humidity less than 80%.
Do not apply the primer-enamel under direct sunlight, strong wind and precipitation. Applied coat shall not be affected with precipitation during 24 hours. Complete hardening and achieving of its properties shall be in 14 hours.
Clean tools with a thinner and then with warm water with detergents if necessary.
Для захисту металевих конструкцій від корозії використовувалася Ґрунт-емаль швидковисихаюча Maxima жовтого кольору.
Для фарбування фасаду використовувалась Гумова фарба Farbex різних кольорів: графіт (RAL 7024), чорний (RAL 9004) …
Для фарбування використовувалась матова чорна ґрунт-емаль швидковисихаюча Maxima та емаль антикорозійна по металу 3 в …
Розмітка та обладнання пофарбовані ґрунт-емаллю швидковисихаючою Maxima.
When calculating the area to be painted, you need to subtract the area that will not be painted. (windows, doors, etc.)
Paint consumption may vary depending on dilution and uniformity of application of the paint.