Delfi
Profi Latex
Interior acrylic latex paint
Specification
It creates a hard, high-quality matt coating, which lets the walls "breathe". It is resistant to repeated washing. It effectively hides micro-cracks on the coated surface. It has а good coverage. It is easy to apply. It doesn't run and splash during application.
Sphere of application
It is intended for interior coating of all mineral (plaster, stucco, brick, concrete), gypsum, and wooden surfaces, wallpaper, and fiberglass. It is recommended for initial and renovating coating of walls and ceilings in dry and wet spaces with high exploitation load: living, administrative premises, medical, infant and educational establishments, premises of catering and industrial enterprises.
Tinting
It is intended for use as a single white coating, or it can be tinted in pastel colors.
It is tinted manually with pigment concentrate Farbex Color, other water-based pastes, or in a tinting machine according to NCS and other color rates. If you tint the paint with other products or catalogs, you must test tinting and application.
To avoid deviation in color shade, we recommend using the product of the same batch for the finishing coat (as the paint, so the colorant). Joint surfaces coated in the same color must be painted with the products of one batch. If you use the product of different batches, mix them before apply.
It is necessary to make a test application on a small area to check if the color corresponds to the chosen one.
We do not recommend diluting the paint for the finishing coat.
After tinting, the technical data of the paint can deviate.
A hint: When you choose a color, take into account the lighting in the premises. Warm and cold light give different color perception of the same color.
Content
Technical data
| Consumption standard of 1 layer | 125-150 g/m2. Depending on the way of application and type of surface. |
| Thinner | Water. It is allowed to dilute it max. 10% of the total weight of the product. |
| Application | It is applied with a roller, a brush or a spraying gun. |
| Drying period (23 °С, 50% RH) | 1 hour. Drying period increases if the temperature falls down, relative air humidity raises, and depends on the consumption of paint (the coat thickness). |
| Solids content (DSTU ISO 3251) |
61±2 % |
| Density (DSTU ISO 2811-1) | ≈ 1,54 g/cm3 |
| Gloss (DSTU ISO 2813) | max. 5 GU at 85°, (dead matt, TSS U EN 13300) |
| The degree of milling (SSU ISO 1524) | max. 30 microns, (fine-grained, TSS U EN 13300) |
| Contrast ratio of dry film (ISO 6504-3) | > 98 %, 2 class of hiding power (acc. to DSTU EN 13300) |
| Wet-scrub resistance, microns (DSTU ISO 11998) |
< 20 (after 200 cycles) |
| Wet-scrub resistance class (DSTU EN 13300) | 2 |
| Warranty period | 24 months from the date of manufacturing (at the temperature from+5 °С till +35 °С) |
| Packaging | 1,4 kg, 4,2 kg, 7 kg, 14 kg |
Gloss
Color
Application instruction
-
1. Surface preparation
Uncoated surface: Clean from the fragile surfaces to a solid base, dust, oil, grease and other dirt.
Previously coated surfaces: Clean thoroughly the surface from old loose coatings (loose paint and varnish) in mechanical (a scraper, a wire brush), thermal (hot air fan, infrared radiation) or chemical way (paint removal solutions). Chalk and lime-chalk coatings shall be removed mechanically till hard surface. Clean the surface also from other dirt. Surfaces, previously coated with alkyd and oil enamel, shall be sandpapered. Then treat it as non-coated surface.
Small defects of mineral surface shall be corrected with finishing putty TM Farbex and sandpaper after that.
For protection against mould and fungi it is recommended to treat the surface with antiseptic TM Farbex.
2. Priming
Previously treated mineral and wood surfaces do not need any undercoating.
Previously untreated absorbing mineral surfaces shall be primed with Acrylic deep-penetrating primer concentrate 1:4 "Profi Base 1:4" TM Delfi. Depending on the type of surface, it is recommended to dilute the primer with water (see the instruction manual of primer).
Previously untreated wooden surfaces shall be undercoated with acrylic wood primer ТМ Maxima.
3. Applying of finishing layer
Stir the paint thoroughly before application. If it is required dilute it with water. Over-dilution makes the quality of the surface worse! Application is performed at the temperature from + 5 °С till + 35 °С. Apply the paint in 1-2 coats with a brush, a roller, or a spraying gun.
4. Tool cleaning
Clean tools with water after application. Do not let them dry. Dry product shall be removed from the tools in mechanical way.
You may also be interested in
Use with this product
References
Акрилова фарба Profi latex TM "Delfi" призначена для фарбування поверхонь всередині приміщень з високим експлуатаційним …
Flow calculator
Consumption standard of 1 layer
When calculating the area to be painted, you need to subtract the area that will not be painted. (windows, doors, etc.)
Paint consumption may vary depending on dilution and uniformity of application of the paint.