Maxima
Parquet Varnish polyurethane-acrylic
Specification
This product creates wearing power of coating. It is resistant to detergent effects. It has a high final hardness, flexibility, and longlasting cover. Besides, the product emphasizes wood fibers and saves its natural look and dries quickly.
Sphere of application
Water-based polyurethane-acrylic parquet varnish is intended for decorative and protective coating of parquet and wooden floors with high operation load. It is also intended for coating of stairs, furniture, window frames, doors, and other wooden surfaces indoors.
Content
Technical data
| Consumption standard of 1 layer | 80-100 ml/m2, depending on the kind of wood and quality of timber as well as way of application. |
| Thinner | Water. Delution of the product is possible but maximum 10% of the total weight. |
| Application | It is applied with a roller, a brush or a . |
| Drying period (23 °С, 50% RH) | 4 hours. Drying period increases if the temperature is getting down and relative air humidity is increasing. Maximum hardness and wear resistance of the coating is achieved after 14 days. |
| Gloss (DSTU ISO 2813) | Glossy. Minimal 60 GU at 60° Silky-matt. Maximal 20 GU at 60° |
| Hardness (DSTU ISO 1522) | > 80 sec.Konig pendulum |
| Solids content (DSTU ISO 3251) | 23±2 %, depending on the gloss degree. |
| Density (DSTU ISO 2811-1) | 1,02 - 1,04 g/сm3, depending on the gloss degree. |
| VOC content (ISO 11890) | < 100 g/l |
| Warranty period | 36 months from the date of manufacturing (at the temperature from +5 °С till +35 °С) |
| Packaging | 0,75 l, 2,5 l, 5 l, 20 l |
Gloss
Color
Application instruction
-
1. Preliminary preparation
The surface shall be dry (maximum humidity is 20%). Clean thoroughly the surface of oils, wax, mud, grease, dust, blue stain, decay, old paint coats and other dirt till clean wood. Clean dirty areas with a dry brush. Mould and plants shall be removed manually (with a scraper or a wire brush). Then treat the surface with Antiseptic for wooden surfaces TM Farbex.
Remove resin at the places of knots in mechanical way.
To receive a smooth surface without visible places of old coatings (paint or varnish), it shall be totally removed from the surface in mechanical (with a scratcher, a floor scrubber), thermal (a hot dryer, infra-red rays) or chemical way (paint removing treatments).
It is not recommended to clean the surface by methods, which can damage wood fibers (for example, sandblast apparatus).
Defected surfaces (holes, rends, cracks) shall be filled with Putty for wood ТМ Farbex. After that, the surface shall be polished up.
Polishing is performed in two steps. The surface is polished up with coarse-grained abrasive paper, then finished with fine-grained abrasive paper.
Remove dust after each preparation. It is also recommended to clean the room from the dust (footstalls, windows, radiators and other elements of interior).
2. Priming
Previously coated wooden surfaces don’t require undercoating.
Previously uncoated wooden surfaces shall be primed.
Check for sure that the surface is clean and completely dry before priming.
It is recommended to prime new or cleaned from old rests surfaces with Wood protective acrylic primer TM Maxima for providing the best defensive effect.
Edges of wooden products shall be treated more carefully and completely impregnated.
3. Applying of finishing layer
Make sure that the primed cover is dry enough before applying the finish coating.
The varnish is ready for use, if needed dilute it with water.
The recommended application of the product is 2-3 layers with intermediate polishing. The next layer shall be applied not earlier, than in 2-4 hours. The final hardening of the surface and the acquisition of its properties occurs 14 days after the coating.
Application is performed at the temperature from + 10 °С to + 30 °С and relative air humidity no more than 80%.
4. Tool cleaning
Clean tools with water after application thoroughly.
You may also be interested in
Use with this product
References
В оформленні інтер'єру зали використовувалася Гумова фарба TM "Farbex" різних кольорів. Гумова фарба TM "Farbex" …
Tips
Як вибрати лак для дерева для внутрішніх і зовнішніх робіт: види лаків
Лак для дерева – це одночасно захист деревини і збереження її природної краси. Дерево вразливий матеріал. Шкідники, дія вологи, перепади температур – все це несе негативний вплив і без захисного покриття деревина швидко втрачає естетичну привабливість і цілісність основи. Хоча …
Які бувають лаки для дерева
Дерево – це той будівельний матеріал, застосування якого можна побачити практично на кожному кроці. Із дерева будують домівки, паркани, роблять меблі та використовують для оздоблення та декору інтер’єра. Завдяки своїй природній красі, унікальній структурі дерево дуже красивий та екологічний матеріал. …
Flow calculator
Consumption standard of 1 layer
When calculating the area to be painted, you need to subtract the area that will not be painted. (windows, doors, etc.)
Paint consumption may vary depending on dilution and uniformity of application of the paint.